1/12 scale body with gleaming display model finish!
●1/12 electric racing car is top of its class for driving or display.
●Polycarbonate pre-cut, printed body.
●Body is equipped with sponsor decals and scale parts. Only a few steps are needed to complete.
●Compatible with 2-cell 7.4V Li-Po or 7.2V Ni-MH batteries.
●Compatible with both 380 and 540 class motors.
●Drive train fully equipped with ball bearings (9 included).
●Compatible with standard size servo and ESC as well as mini servo.
●Easily detachable large-size diffuser improves rear traction.
Unrestricted battery choice with a multi design
PLAZMA Lm does not restrict the type of battery to be used. Two battery holders included can suit most NiMH, Li-Po and Li-Fe batteries available on the market. From slightly older and larger 7.4V Li-Po s to the latest ORION TS and RC PLANNING R246 Muscle Power series batteries or short size and 1-cell size Li-Po batteries used in 1/12 racing, nearly all batteries for 1/12 and 1/10 models can be installed.
1990 NISSAN R90CP No.23
In 1990 Nissan ended its partnership with Lola in the development of the R89C for the LeMans 24 hour race and embarked independently on the development of a new machine. This machine was the R90CP. While its basic center monocoque package was adopted from the R89C, a newly designed cowl produced improved aerodynamics and the evolutionary V8 turbo VRH35Z engine delivered dramatic improvements in racing potential.
The R90CP made its debut in the domestic Japanese championship and continued to enhance its performance with repeated race activity. The next challenge was the LeMans. Nissan entered 7 machines in that year, but only one R90CP, No.23 driven by Japanese trio Masahiro Hasemi, Kazuyoshi Hoshino and Toshio Suzuki. Having posted 3rd place in the heat, the R90CP maintained good position in the final race despite minor mechanical troubles, while other Nissan cars fell back. With one hour to go a gearbox change was required, but was executed in only 11 minutes, allowing the R90CP to claim 5th place, the best finish of any Japanese car and driver combination in 1990.
Copyright c San-eishobo Publishing Co.,Ltd.All Rights Reserved.
Equipped with pre-cut, printed body and a full set of scale parts. Only a few finishing steps are needed for a display model standard.
Main chassis, lower pad plate and chassis brace are all made from carbon. No compromise has been made in the pursuit of speed.
Race specification sponge tires included. Printed logo delivers the finishing touch for enhanced scale appearance. Pre-glued to wheels so you can realize top performance straight away.
Included multi-motor mount is compatible with 540 and also 380 class motors. Plenty of motor slide allows for a wide selection of gear ratios.
Front suspension features king pin strut system. Allows for precision alignment adjustment of camber, caster, tread etc.
FRP T-bar rear suspension controls roll direction with rear side friction tube and pitching direction with constant volume diaphragm shock absorber.
PLAZMA Lm does not restrict the type of battery to be used. Two battery holders included can suit most NiMH, Li-Po and Li-Fe batteries available on the market. From slightly older and larger 7.4V Li-Po’s to the latest ORION TS and RC PLANNING R246 Muscle Power series batteries or short size and 1-cell size Li-Po batteries used in 1/12 racing, nearly all batteries for 1/12 and 1/10 models can be installed.
Radio compartment is large enough to comfortably fit standard size servo, ESC and receiver. (Mini-servo from Ra can also be installed).
Drive shafts fully equipped with ball bearings. (total 9)
- TECHNICAL DATA
■Ground Clearance: 6mm approx.
■Tire(F/R): Φ56×36.5mm / Φ54×36.5mm
■Gear Ratio: 1:3.875
■Weight: 900g approx.
■Motor: 380 or 540 type (sold separately)
- KIT CONTENTS
●Chassis assembly kit
●Semi-completed body (in package color)
●Silicone oil #500/#10000
●Ball diff. grease
●Cross wrench （7/5.5mm）
●Hex wrench （8/7mm） *plastic material
●L wrench（3/32inch, 1.5/2.0/2.5/3.0mm）
- REQUIRED FOR OPERATION
＜Required for operation＞
●2ch RC system with 1 servo
●380 or 540 type motor
●7.2V Ni-MH battery / 7.4V Li-Pobatery / 6.6V Li-Fe battery
●Battery for RC system